# $Id: class2.0,v 1.12 1996/06/24 02:58:33 sam Rel $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Generic Class 2.0 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 1 AreaCode: 905 FAXNumber: +1.905.472.5732 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0644 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: on GettyArgs: "-h %l dx_%s" LocalIdentifier: "IIS" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%p of %%t" QualifyTSI: MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2.0 # use this to supply a hint ModemRate: 38400 ModemFlowControl: rtscts ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # ModemDialCmd: ATDT%s # T for tone dialing, @ for silence # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: "" # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer ModemNoFlowCmd: AT&H0&I0&R1 ModemHardFlowCmd: AT&H1&I0&R2 ModemSoftFlowCmd: AT&H2&I2&R1 # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" ModemEchoOffCmd: ATE0 # disable command echo ModemVerboseResultsCmd: ATV1 # enable verbose command results ModemResultCodesCmd: ATQ0X4 ModemOnHookCmd: ATH0 # place phone on hook (hangup) ModemSoftResetCmd: ATZ # do soft reset of modem ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds ModemRecvFillOrder: LSB2MSB # bit order of received facsimile ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2.0 modems. # Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0 Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct) Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FKS # abort session command Class2CQQueryCmd: !(0),(0) # query for copy quality capabilities Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities Class2TBCCmd: AT+FPP=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter Class2BUGCmd: AT+FBU=0 # enable HDLC frame tracing Class2LIDCmd: AT+FLI # set local identifier command Class2DCCCmd: AT+FCC # set modem capabilities command Class2DISCmd: AT+FIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FPI # set polling identifier command Class2NRCmd: AT+FNR=1,1,1,0 # setup status reporting command Class2PIECmd: Class2PTSCmd: AT+FPS # set post-page status command Class2SPLCmd: AT+FSP # set polling indicator command Class2NFLOCmd: AT+FLO=0 # set no flow control command Class2SFLOCmd: AT+FLO=1 # set software flow control command Class2HFLOCmd: AT+FLO=2 # set hardware flow control command