# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:  49
AreaCode:  421
FAXNumber:  +49.421.5490519
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing:  527
SessionTracing:  527
RecvFileMode:  0644
LogFileMode:  0600
DeviceMode:  0666
RingsBeforeAnswer: 1
SpeakerVolume:  off
GettyArgs:  "-r -b -s %s %l"
LocalIdentifier: "D C P  Bremen"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
# QualifyTSI:  etc/tsi
QualifyTSI:
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class2  # use this to supply a hint
ModemRate:  19200  # max rate for DCE-DTE communication
ModemFlowControl: rtscts  # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D3  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:  AT$1=1DP%s@ # T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:  ""  # stuff to do when modem is reset
ModemAnswerCmd:  ATA  # use this to answer phone
ModemNoFlowCmd:  AT\Q0  # disable flow control cmd
ModemHardFlowCmd: AT\Q3  # hardware flow control cmd
ModemSoftFlowCmd: AT\Q1  # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0  # disable command echo
ModemVerboseResultsCmd: ATV1  # enable verbose command results
ModemResultCodesCmd: ATQ0  # enable result codes
ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
ModemSoftResetCmd: ATZ  # do soft reset of modem
ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:  AT+FCLASS=2 # command to enter class 2
Class2BORCmd:  AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd:  AT+FOPT=1,0 # byte-align EOL codes on recv
Class2CQCmd:  ""  # commands to enable copy quality proc.
Class2AbortCmd:  AT+FK  # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd:  AT+FTBC=0 # setup stream mode
Class2CRCmd:  AT+FCR=1 # enable capability to receive
Class2PHCTOCmd:  AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd:  AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd:  AT+FLID  # set local identifier command
Class2DCCCmd:  AT+FDCC  # set modem capabilities command
Class2DISCmd:  AT+FDIS  # set session parameters command
Class2DDISCmd:  ""  # disable pre-dial DIS command hack
Class2CIGCmd:  AT+FCIG  # set polling identifier command
Class2PTSCmd:  AT+FPTS  # set post-page status command
Class2SPLCmd:  AT+FSPL  # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: ""  # character sent to modem to start recv
Class2XmitWaitForXON: yes  # if true, wait for XON before send