# $Id: usr-xon,v 1.4 2001/02/05 06:38:34 darren Exp $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Configuration for using the Class 1 command interface with # a USR Courier or Sportster modem and XON/XOFF flow control. # # CountryCode: 49 AreaCode: 541 FAXNumber: +49.541.0815 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "NothingSetup" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use class 1 interface ModemRate: 38400 # max rate for DCE-DTE communication ModemFlowControl: xonxoff # hardware flow control # ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control ModemResultCodesCmd: ATQ0X4 # enable result codes # ModemMfrQueryCmd: !USR ModemModelQueryCmd: ATI3 ModemRevQueryCmd: ATI7 # XXX returns a multi-line result # # When AT+FCLASS=1 is issued the modem automatically switches # to software flow control; these parameters let the fax software # reset flow control as needed after entering Class 1. # Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control Class1SFLOCmd: "" # modem does this automatically # # The remainder of this configuration is included so that the # modem "idles" in Class 0 while not sending or receiving facsimile. # ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0 ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1 # # Disables the reporting of bad frames by the modem. This # overcomes a firmware problem in the x2 and V90 Sportsters. # It is not necessary for the Courier modem. # Class2NRCmd: AT+FNR=1,1,1,0