# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $ # # HylaFAX Facsimile Software # # # Generic Class 2 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # # BEGIN-SERVER CountryCode: 49 LongDistancePrefix: 0 InternationalPrefix: 00 AreaCode: 0761 DialStringRules: etc/dialrules FAXNumber: +49.xxx.xxx.xxx LocalIdentifier: "+49.xxx.xxx.xxx" # default is canonical FAXNumber ServerTracing: 1 # log server-related operations SessionTracing: 11 # log server-related operations RecvFileMode: 0644 # recvd facsimile are public readable LogFileMode: 0644 # public log files DeviceMode: 0600 # device is accessible only to uucp/fax GettyArgs: "" # requires modem to auto-detect fax/data SpeakerVolume: off # machine's are already too loud RingsBeforeAnswer: 3 # answer on third ring TagLineFont: etc/lutRS18.pcf # tag line font TagLineFormat: "Von %%l|%c| Seite %%p von %%t" MaxBadCalls: 5 # max 5 consecutive bad calls PostScriptTimeout: 300 # 5 minute timeout on PostScript jobs MaxSendPages: 25 # max pages in an outbound job MaxRecvPages: 25 # max pages in an inbound job ContCoverPage: etc/cover.templ # enable continuation cover pages DestControls: etc/destcontrols # destination-specific controls MaxConcurrentJobs: 1 # serialize jobs to the same dest TimeOfDay: "Any" # outbound jobs any day, any time # END-SERVER # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2 # use this to supply a hint ModemRate: 19200 # max rate for DCE-DTE communication ModemFlowControl: rtscts # RTS/CTS flow control assumed ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # ModemDialCmd: ATDT0W%s # T for tone dialing, @ for silence, 0W for PBX # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: "" # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone ModemNoFlowCmd: AT&K0 # disable flow control cmd ModemHardFlowCmd: AT&K6 # flow control recommended for fax ModemSoftFlowCmd: AT&K6 # flow control recommended for fax ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # ModemSetVolumeCmd: "ATL0 ATL1 ATL2 ATL3" ModemEchoOffCmd: ATE0 # disable command echo ModemVerboseResultsCmd: ATV1 # enable verbose command results ModemResultCodesCmd: ATQ0 # enable result codes ModemOnHookCmd: ATH # place phone on hook (hangup) ModemSoftResetCmd: ATZ # do soft reset of modem ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds ModemRecvFillOrder: MSB2LSB # bit order of received facsimile ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2 modems. # Class2Cmd: AT+FCLASS=2 # command to enter class 2 Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct) Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FK # abort session command Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities Class2TBCCmd: AT+FTBC=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing Class2LIDCmd: AT+FLID # set local identifier command Class2DCCCmd: AT+FDCC # set modem capabilities command Class2DISCmd: AT+FDIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FCIG # set polling identifier command Class2PTSCmd: AT+FPTS # set post-page status command Class2SPLCmd: AT+FSPL # set polling indicator command # # If Class2RecvDataTrigger is not set, then it is set to DC1 # Class2RecvDataTrigger: "" # character sent to modem to start recv Class2XmitWaitForXON: yes # if true, wait for XON before send