| Config |
# $Id: usr-2.0,v 1.2 1999/01/04 10:19:07 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode: 1
AreaCode: 709
FAXNumber: 466-7489
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "PHCC"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 38400 # DCE-DTE communication rate
ModemFlowControl: rtscts # XON/XOFF flow control assumed
#
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemResultCodesCmd: ATQ0X4 # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
# the modem is left idling in Class 2.0
#
ModemSetupAACmd: AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd: AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd: !(0),(0) # override modem response
#
# Disables the reporting of bad frames by the modem. This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd: AT+FNR=1,1,1,0 |
e31b.tmp.upload.ttys1 ( bytes)
