Modem Configuration Data for Hylafax supported by Xtreme Webdesign Fa. T. Mueller www.xtremeweb.de
Config ID = f8b1

Manufacturer Elsa
Model Microlink 28.8 TQV, 33.6 TQV, 33.6 TS, 56K, ISDN/TLV.34
Operation Mode Class 2.0 RTSCTS
Config
#
# Class 2.0 modem configuration for ELSA Microlink with Hayes command set
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            49
AreaCode:               241
FAXNumber:              +49.241
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "+49.241"
LogFacility:            local7
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "Von %%l|%c|Seite %%p von %%t"
PercentGoodLines:       80
MaxConsecutiveBadLines: 20
MaxRecvPages:           250
ModemPriority:          200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              115200          # max rate for DCE-DTE communication
ModemFlowControl:       rtscts          # RTS/CTS flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers (e.g. 9) to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9W%s@".
#
ModemDialCmd:           ATDT%s
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:                ATX3            # stuff to do when modem is reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT\Q0
ModemHardFlowCmd:       AT\Q3
ModemSoftFlowCmd:       AT\Q1
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command
Download config f8b1.upload.config (4830 bytes)
Firmware-Downloadlink http://www.elsa.de
Comments
Taken from the ELSA-Homepage and PBX-prefix added.
Works well with Microlink 33.6 TQV
Name Andreas Hoedle
E-Mail hoedle@kwsoft.de
Entered 149.225.56.143 2000/07/14 11:30


modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)modify the informationdelete entire recordHOMELOGIN (you are guest)   Web Oriented Database Home