Config |
# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $
#
# HylaFAX Facsimile Software
#
#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
# BEGIN-SERVER
CountryCode: 49
LongDistancePrefix: 0
InternationalPrefix: 00
AreaCode: 0761
DialStringRules: etc/dialrules
FAXNumber: +49.xxx.xxx.xxx
LocalIdentifier: "+49.xxx.xxx.xxx" # default is canonical FAXNumber
ServerTracing: 1 # log server-related operations
SessionTracing: 11 # log server-related operations
RecvFileMode: 0644 # recvd facsimile are public readable
LogFileMode: 0644 # public log files
DeviceMode: 0600 # device is accessible only to uucp/fax
GettyArgs: "" # requires modem to auto-detect fax/data
SpeakerVolume: off # machine's are already too loud
RingsBeforeAnswer: 3 # answer on third ring
TagLineFont: etc/lutRS18.pcf # tag line font
TagLineFormat: "Von %%l|%c| Seite %%p von %%t"
MaxBadCalls: 5 # max 5 consecutive bad calls
PostScriptTimeout: 300 # 5 minute timeout on PostScript jobs
MaxSendPages: 25 # max pages in an outbound job
MaxRecvPages: 25 # max pages in an inbound job
ContCoverPage: etc/cover.templ # enable continuation cover pages
DestControls: etc/destcontrols # destination-specific controls
MaxConcurrentJobs: 1 # serialize jobs to the same dest
TimeOfDay: "Any" # outbound jobs any day, any time
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # RTS/CTS flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDT0W%s # T for tone dialing, @ for silence, 0W for PBX
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K0 # disable flow control cmd
ModemHardFlowCmd: AT&K6 # flow control recommended for fax
ModemSoftFlowCmd: AT&K6 # flow control recommended for fax
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATL0 ATL1 ATL2 ATL3"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "" # character sent to modem to start recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
|